Desk chair mount
Desk chair mount
Desk chair mount
Desk chair mount
Desk chair mount
Desk chair mount
Desk chair mount
Desk chair mount

Desk chair mount

€114,00
€114,00
Sold out
Tax included. Shipping calculated at checkout.

Desk chair mount on back order, shipment end of Februari

Unfold the CoffeeRacer, roll your desk chair towards it, lock the tilt of your chair and lower your chair onto the CoffeeRacer… and you're off!

effectively your chair and the CoffeeRacer have become one! no more movement, no more swivel! You now have a no-compromise Sim racing setup!

Dismounting from the CoffeeRacer, simply tilt back the chair using the tilt function. And slide the chair mount under your chair and no one will notice the semi professional simrig in your room!

this combination truely supports proffessional sim racing equipment, including load-cell braking systems. It has all the advantages of a permanent setup, without being a permanent eyesore and room hogger (to anyone but you obviously).

the desk chair mount has been tested on the ADAC sim expo (conbined with a coffeeracer play, a secretlab titan 2022, simucube sport 2 and heusinkveld sprint pedals) by proffessional simracers, streamers, wheel/pedal manufacturers and gear reviewers and they were all really exited about the stability, the comfortability and the driving experience.

The desk chair connector is designed for gaming chairs with a hole pattern of 20 x 19,50 cm underneath the seat. This includes common chairs such as the Secretlab and Noble chairs. Anything close to this pattern might also work if you posess some DIY skills, Unfortunately, the bottom Herman Miller & Recaro chairs are quite specific so at this point CoffeeRacer has no solution for these chairs.

The desk chair mount works on both the CoffeeRacer 'Play' and the CoffeeRacer 'Go'. With the CoffeeRacer 'Play' you simply put the weight of the chair onto the CoffeeRacer and you are connected. With the CoffeeRacer 'Go' you need to replace the feet for the optional wheels to get the right seating position. A large bolt is provided to connect the desk chair mount with the CoffeeRacer as well. In 99% of the seating positions you do not need to use this, your weight will hold it all together.

Materials: 3mm steel

Powdercoating: black metallic, fine textured

 

 

Customer Reviews

Based on 2 reviews
100%
(2)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
G
Gianluca B.
Almost mandatory for coffeeracers!

When I bought my CoffeeRacer I didn't take the chair mount as well, this because in that moment wasn't available. Being on the shorter side and using a simple G920, chair swivel was quite reduced and my braking force was light enough to keep the CR in place just by using caster brakes. Nevertheless, when upgrading to a load cell brake chair mount became almost mandatory, since I was pushing away my chair at each brake, forcing myself to grab the wheel and keep pulling while braking. Clearly this was not a sustainable approach which was killing my lap times as well. After installing the chair mount my braking became much more consistent and my session less tiring. To sum up, if you bought a CR play this is almost mandatory since without it your chair will swivel and it is likely that you'll push either the CR or the chair away when braking. The unique case in which it may not necessary is when you are short enough to keep the chair close enough to the CR to avoid swivel and you have a very light foot. Nevertheless, when you start experience braking at full force without destroying your setup you won't come back!

The mounting process is fast and compatible with the majority of chairs. Clearly, the chair mount adds a little overhead to the setup process, but is less than a minute.

F
Fabio Hipolito
The companion to the coffee racer is a perfect chair mount. Could not recommend more!

Clean and neat design that transforms an office chair into a very good and stable racing seat. Do not underestimate its robustness, just find your fit and it will hold the chair firmly onto the rig, while being just as discrete as the rest of the products.
The design is on par with the high standards and quality of the coffeeracer products. The past three weeks have been amazing, I recommend investing a sometime exploring the large number of seating positions, it is worth! :-)

If you have a chair that does not match the mount points, inspect its bottom plate, it should be possible to drill the chair's bottom plate and insert metal threads for screws. For the 'håg secret room', remove the bottom wood plate, drill four holes and inset metal threads for M6 screws, a few washers, spacers, and nuts will do the job.